Water Heater Burst? What Greenville Homeowners Should Do Next

A burst water heater can empty a full tank onto your floor in minutes, and keep going. Here's what to do right now, why tanks give out, and the small fixes that keep yours from being next.

TL;DR: If your water heater burst, shut off the cold water valve on top of the tank (or the main), turn off the power or gas, and stay clear of hot water. Smell gas? Leave the house and call 911 or Piedmont Natural Gas at 800-752-7504 from outside. A burst tank can't be repaired, only replaced. The good news: most bursts give warning signs first, and a few inexpensive checks make one far less likely.

A water heater burst is one of the few plumbing problems that can flood a garage in the time it takes to find your shoes. A standard tank holds 40 to 50 gallons, and the water line feeding it keeps refilling it until someone shuts it off.

We'd rather you never need this post. But if you're reading it with wet socks, start with the next section and come back for the rest later.

Your Water Heater Burst. Do This Now.

  1. Keep clear of the water near the tank. It can be hot enough to scald, and it may be reaching cords, outlets, or your electrical panel. If it is, don't wade in.
  2. Shut off the cold water supply. The valve is on the pipe going into the top of the tank. If you can't reach it safely, shut off the main water valve to the house.
  3. Turn off the power or gas. Flip the water heater breaker for an electric unit. Turn the gas control knob to "Off" for a gas unit.
  4. Open a hot water faucet somewhere in the house to relieve pressure in the lines.
  5. Move what you can and start removing water. Towels, a shop vac, a squeegee toward a floor drain or the garage door.
  6. Take photos of the heater, its label, and the damage before you clean up. Your insurance company will want them.
  7. Call us at (864) 313-1289.

If you smell gas (a rotten egg odor), skip everything above. Get everyone out, then call 911 or Piedmont Natural Gas from outside.

Our emergency water heater repair guide walks through each of these steps in more detail, including how to find your breaker and gas valve.

Can a Water Heater Explode?

Yes, but it's rare, and it's not what usually happens. When people say their water heater burst, they almost always mean the tank split or rusted through and dumped its water. That's a mess, not a blast.

A true explosion takes two failures at once. First, the thermostat or gas control sticks on and keeps heating. Second, the temperature and pressure relief valve (the T&P valve) fails to open. Water trapped past boiling under pressure flashes to steam the instant the tank gives way, and that's what sends a tank through a roof.

The T&P valve is there to stop that from ever happening. On a typical home water heater it opens at 150 psi or 210°F, whichever comes first. As long as it works and nobody has capped it, an explosion is extremely unlikely. That's why we treat a T&P valve that's dripping, corroded, or plugged as a real problem, not a nuisance.

Why Water Heaters Burst

Most bursts come down to one of these.

Corrosion from the inside. A tank water heater is a steel tank with a glass lining. A metal anode rod inside the tank corrodes on purpose so the tank doesn't. Once that rod is used up, the tank starts rusting at its weakest spot until it finally lets go. Greenville's water is naturally soft, so we see less heavy sediment here than plumbers in hard water parts of the country do. Corrosion is a different story. Every steel tank rusts once its anode rod is gone.

Too much pressure. Water expands when it heats. In many homes, a check valve, backflow preventer, or pressure reducing valve keeps that extra volume from pushing back into the city line. It has nowhere to go, so pressure climbs every time the heater runs. An expansion tank absorbs it. Without one, the tank flexes over and over, and the relief valve wears out. High street pressure adds to it. Most plumbing codes cap household water pressure at 80 psi.

A relief valve that can't do its job. We've found T&P valves that were plugged, capped, corroded shut, or piped into a line that was blocked. A tank with no working relief valve has no safety net.

Overheating. A failed thermostat or gas control can keep heating past the set temperature. Scalding water at the tap or a relief valve that keeps blowing are the clues.

Age. Most tank water heaters last about 8 to 12 years. Past that, every year is borrowed time.

Warning Signs Before a Water Heater Bursts

Tanks rarely fail without a hint. Call us if you notice any of these:

Our guide to the signs your water heater needs replacing goes deeper on each one.

How to Keep Your Water Heater From Bursting

None of this is expensive. Most of it costs nothing.

CheckHow oftenWho
Test the T&P valve: lift the lever briefly, it should release water and snap shutOnce a yearYou
Set the thermostat to 120°FOnceYou
Flush the tankOnce a yearYou or us
Check that you have an expansion tank, and that it still holds its air chargeAt install, then every few yearsUs
Inspect the anode rod and replace it if it's worn downEvery few years, starting around year 3Us
Check your home's water pressure (under 80 psi)Once, or when faucets start acting upYou (a hose bib gauge is inexpensive) or us
Put the tank in a drain pan and add a leak sensorOnceYou or us

A note on testing the T&P valve: if yours has never been tested and the tank is older, the valve may not seat again and could keep dripping. Have a bucket ready. If it won't stop, call us. Better to find that out now than when the valve is needed.

The U.S. Department of Energy recommends 120°F for most homes. It saves energy and lowers the risk of scalding. Here's how often to flush your water heater and how to do it.

If your heater doesn't have an expansion tank and your home is a closed system, adding one usually runs a few hundred dollars installed. That's a small fraction of what a new water heater and a wet garage cost.

What a Burst Water Heater Costs

A burst tank means a new water heater. A standard 40 to 50 gallon tank runs roughly $800 to $2,500 installed in the Greenville area, depending on the unit and what the install needs.

The water damage is the bigger wildcard. Dry everything out fast. The EPA recommends drying wet materials within 24 to 48 hours to keep mold from taking hold. Many homeowners policies cover sudden water damage to the house but not the water heater itself when it failed from age. Check your policy, and keep those photos.

When we replace a burst heater, we look at why it failed. That means an expansion tank where your system needs one, a relief valve piped the right way, and a drain pan where it makes sense. Fixing the cause is what keeps the next one from doing the same thing. If you're weighing a new unit anyway, our tankless vs. tank comparison is worth a read.

Burst Tank? Call Your Neighbors in Taylors

Plumbing Heroes is owner-operated and based in Taylors. We serve homeowners across Greenville, Greer, Taylors, Simpsonville, Mauldin, and Travelers Rest. We handle emergency plumbing during normal business hours. If your tank bursts after hours, the steps above make it safe to wait: water off, power or gas off, and it stops getting worse. Call us first thing or book online tonight and we'll reach out.

And if your water heater is just showing a few of the warning signs above, call us before it gets to that point. Sometimes it's a $150 part. We'll tell you straight either way.

Call (864) 313-1289 or learn more about our water heater repair and replacement services.

FAQ

Q: What happens when a water heater bursts?

A: Usually the tank splits or rusts through and dumps its water, then keeps leaking as the supply line refills it. You'll see water spreading from the base, sometimes with steam. Shut off the cold water valve on top of the tank and the power or gas right away.

Q: Can a water heater explode?

A: It can, but it's rare. An explosion needs the heater to overheat and the temperature and pressure relief valve to fail at the same time. A working relief valve opens before pressure or temperature gets dangerous, which is why it should be tested once a year and never capped or plugged.

Q: Can a burst water heater be repaired?

A: No. Once the tank itself has failed, it has to be replaced. Leaks from fittings, valves, or pipes around the tank are a different story and are often repairable.

Q: How do I know if my water heater is about to burst?

A: Watch for water or rust at the base, rusty hot water, a dripping or hissing relief valve, popping or banging noises, or a tank that looks bulged. A tank over 10 years old with any of these signs is worth having checked soon.

Q: Does homeowners insurance cover a burst water heater?

A: Many policies cover sudden water damage to the home but not the water heater itself when it failed from age or wear. Take photos before cleanup and check your policy. We can document what failed for your claim.

Q: Do I need an expansion tank on my water heater?

A: If your home has a check valve, backflow preventer, or pressure reducing valve on the water line, it's a closed system, and plumbing codes generally require thermal expansion control. An expansion tank is the usual fix. We check for this whenever we install or service a water heater.

Q: How fast can you replace a burst water heater in Greenville?

A: For a standard tank swap, it's often quick. Call us at (864) 313-1289 and we'll give you a straight answer on timing based on what you have and what's in stock.

‍

Ready to Call in Your
Local Plumbing Heroes?

Whether you’re dealing with an urgent plumbing issue or planning improvements for your home, our team is ready to help. Upstate homeowners trust Plumbing Heroes for dependable service, clear communication, and work that stands the test of time.